BC
BurnerCRM
•6 min read•Aaron Allen

What Insurance Does a Stove Installation Business Actually Need?

HETAS sets a £2m public liability minimum, but that's not the whole picture. Here's what's legally required, what's optional, and where installers most often find themselves underinsured — public liability, employers' liability, tools in transit, and professional indemnity.

Most installers have public liability insurance sorted because HETAS won't let you register without it. Fewer have stopped to check whether that's the only cover they need, or whether a van full of tools and a Saturday job gone wrong could still leave them exposed. Here's what actually matters, what's a legal requirement versus what's just sensible, and where the gaps tend to show up.

Public liability: the one HETAS makes you have

HETAS requires members to carry a minimum of £2 million public liability insurance as a condition of staying on the competent persons scheme. This is the cover that pays out if you damage a customer's property or someone gets hurt because of your work: drop a flue liner through a ceiling, knock a stove flue pipe loose and it leaks fumes, or a customer's dog trips over your tools and breaks a wrist.

£2 million is the floor, not necessarily the right number. If you're fitting multi-fuel stoves into listed buildings or period properties with expensive finishes, a single claim for smoke or water damage to original features can run well past that. Many installers carry £5 million or £10 million instead, and the price difference between the levels is usually smaller than people expect. On average, small UK businesses pay around £118 a year for public liability cover, though that figure moves a lot depending on turnover, claims history and the type of work, so it's worth getting your own quote rather than budgeting off an industry average.

Employers' liability: compulsory the moment you take on staff

This is the one that catches installers out after they read our piece on taking on your first employee. The moment you have anyone working for you, whether that's a full-time fitter or a labourer helping out on big jobs, employers' liability insurance becomes a legal requirement under the Employers' Liability (Compulsory Insurance) Act 1969. The minimum cover level is £5 million, and going without it can bring a fine of up to £2,500 for every day you're uninsured.

There are narrow exemptions: businesses with no employees, and unincorporated family businesses where everyone on the payroll is a close relative. If you're a sole trader working alone, this doesn't apply to you yet. The day you bring someone on, even casually or for a few weeks during the busy season, it does.

Tools in transit: the gap most installers don't know they have

Ask most installers whether their van insurance covers the £3,000–£8,000 of tools sitting in the back, and a lot of them assume it does. It usually doesn't. Standard van insurance covers the vehicle itself, not the contents, which means a smashed window and a stolen tool kit is a loss you're carrying yourself unless you've added separate cover.

Tool or "contents" insurance for tradespeople typically covers up to £10,000 of kit with an excess around £100, but it comes with conditions worth reading properly before you assume you're covered: many policies exclude tools left in the van overnight, most require visible signs of forced entry to pay out on a theft claim (so an unlocked van is a problem), and some insurers want a specific standard of van security, like an alarm covering both the front and rear doors. Keep receipts for anything expensive. Payouts on older tools are often reduced for wear and age, and a receipt is the easiest way to argue your corner.

Professional indemnity: usually optional, sometimes worth it

Professional indemnity covers claims that your advice or design work was negligent, rather than your physical work damaging something. For most installers doing straightforward fit-and-sweep work, this sits lower down the priority list than public and employers' liability. It starts to matter more if you're doing design work on bespoke installations, signing off compliance paperwork that a customer later relies on for a house sale, or advising on flue routing for unusual builds where getting the spec wrong could mean a full re-install. If any of that describes a chunk of your work, it's worth a conversation with a broker rather than assuming it doesn't apply.

Where this sits next to your insurance-backed guarantee

It's easy to mix up your business insurance with an insurance-backed guarantee, but they protect different things. Your public liability and employers' liability cover is about protecting your business if something goes wrong during or shortly after the job. An insurance-backed guarantee protects the customer's deposit and your workmanship guarantee if your business itself stops trading. You can have excellent business insurance and still leave a customer exposed if you go under with their deposit in your account and no IBG in place, which is exactly the scenario HETAS-aligned guarantee schemes exist to close.

What to actually check with your broker

Rather than buying cover off a generic small business comparison site, go to a broker who specifically writes policies for stove and heating installers, or one who at least understands HETAS requirements. Ask them to confirm, in writing, that your public liability policy meets the £2 million HETAS minimum, that your tools cover matches what's actually in the van (not what was in it when you took the policy out two years ago), and whether your policy excludes anything specific to solid fuel work, like chimney fires or carbon monoxide claims. A policy written for general tradesmen sometimes carries exclusions that only become obvious when a flue-related claim gets refused.

Keeping the paperwork where you can find it

The annoying part of all this isn't working out what cover you need, it's being able to put your hands on the right certificate when a customer, a mortgage valuer, or HETAS itself asks for proof. Renewal dates for public liability, employers' liability and your HETAS registration rarely line up, and a lapsed policy you didn't notice is worse than never having had the right level of cover in the first place.

This is one of the quieter jobs BurnerCRM takes off your plate: store your insurance certificates and renewal dates against your business profile alongside your HETAS reference numbers, flue liner warranties and job completion photos, so everything a customer or inspector might ask for is in one place rather than scattered across old emails and a folder on your phone.

Stay in touch

Want help choosing the right CRM for your installation business?

If this article hit on a problem you are trying to solve, send us a quick note. We’ll reply personally and help you decide whether BurnerCRM fits your workflow.